 
PROJECT DATA
------------
Project            : 
Designer           : 
Date               : May/24/2023
Checked By         : 
Date Checked       :  
User job number    : 
State              :                               State Job #: 
State Specification: None                         
Comments           : B42 Construction Load Check (LEAP Concrete Version 21:00:00:24):
                     (1)The bridge span is 42'-6", girder spacing is 7.5 feet, and deck overhang width is 3 feet 
                     and 1 inch.
                     (2)The structural depth of the deck and sacrificial wearing surface are assumed to 7.75 and 
                     0.75 inches, respectively. The thickness of the overhang tapers from 11 inches at the beam 
                     flange to 10 inches at edge of deck.
                     (3)The structural haunch thickness is 0.5 inches and the haunch thickness for calculating its 
                     dead load is 1.0 inches.
                     (4)One steel diaphragm of 0.285 kips is at the center of span.
                     (5)Dead load of forms: 0.010 ksf on the tributary area of the deck width with a 1.50 load 
                     factor. This load is applied to the full span length.
                     (6)Dead load of edge rail and walkway applied at the edge of the deck form: 0.075 klf [IDOT SS 
                     2403.03, L, 4, d.] with a 1.25 load factor. This load is applied to the full span length.
                     (7)Construction live load on walkway: 0.050 ksf [IDOT SS 2403.03, L, 4, e.] on a 2-foot wide 
                     walkway with a 1.50 load factor. This load is applied to the full span length.
                     (8)Construction live load on deck: 0.050 ksf [IDOT SS 2403.03, L, 4, e.] on the tributary area 
                     of the deck width with a 1.50 load factor. This load is applied from midspan to end of span.
                     (9)Live load of finishing machine located along the edge of the deck form to maximize the 
                     design condition: 9 kips with a 1.50 load factor. The load is placed as 4 individual point 
                     loads of 2.25 kips spacedon 2-foot centers with one of the middle point loads located at the 
                     center of the span.
                     NOTE:
                     The Final Stress limit for tension in the bottom flange for Service III, is set at zero, per 
                     BDM 5.4.1.4.1.3. 
                     It is permissible for the Service III tensile stress to exceed zero at the top flange near the 
                     beam ends, as long as it is within the 0.24?(f?c)0.5 tension limit at release.    
Design Mode        : AASHTO LRFD - 8th Edition
Units:             : US
Design as:         : Simple span
Flared Girder:     : No
File Name          : c:\users\9925\appdata\local\temp\1\leap_bak\lb_1295.tmp\B42_Construction\BR01.csl
 
 
GEOMETRY DATA
--------------
 
BRIDGE LAYOUT                                 
-------------                                 
Overall width     , ft  =       36.333
Left curb         , ft  =        0.000
Right curb        , ft  =        0.000
curb-to-curb width, ft  =       36.333
Number of spans         =            1
Number of lanes         =            3
Lane width        , ft  =       12.000
Eff Deck thick    , in  =        0.000
Sacrificial thick , in  =        0.000
Haunch thickness  , in  =        0.000
Haunch width      , in  =        0.000
Bridge c/s,MI(Ixx), in4 =    310000.00
 
SPAN DATA
---------
Precast length    , ft =     43.500
Bearing-to-bearing, ft =     42.500
Release span      , ft =     43.500
 
BEAM DATA
---------
 No               ID    Loc-prev    Area     MI(Ixx) Height   Yb   B-topg  B-Trib
                             ft      in2       in4     in     in     in      ft
 1             IA-Std-B    3.167    382.5    62000.0  39.00  17.06  13.00   6.917
 2             IA-Std-B    7.500    382.5    62000.0  39.00  17.06  13.00   7.500
 3             IA-Std-B    7.500    382.5    62000.0  39.00  17.06  13.00   7.500
 4             IA-Std-B    7.500    382.5    62000.0  39.00  17.06  13.00   7.500
 5             IA-Std-B    7.500    382.5    62000.0  39.00  17.06  13.00   6.916
 
 
MATERIAL DATA - Project Level
-----------------------------
 
As defined in Material Tab. For beam level properties look at Beam Specific output.
 
CONCRETE PROPERTIES
-------------------
                   Precast          C.I.P.
f'c ,ksi      =      5.000           4.000
Wc  ,pcf      =    150.000         150.000
Concrete Type =     Normal          Normal
Lambda        =      1.000           1.000
Ec  ,ksi      =   4286.830        4266.220
K1            =      1.000           1.000
f'ci,ksi      =      4.500 
Eci ,ksi      =   4066.840
K1            =      1.000
Thermal coeff.,1/F  = 0.00000600
 
STRAND AND REBAR PROPERTIES
----------------------------
PRESTRESSED STEEL:
0.6''-LL-270-72.6, Low relaxation strands 
     Straight Pattern
     Strand Diameter       =        0.600 in
     Tensile Strength(fpu) =      270.0 ksi
     Strand Area           =        0.217 in2
Use transformed strand and rebar: Strand Only
 
REINFORCING STEEL: Tension/Shear steel: fy = 60.0 ksi Es =  29000 ksi
 

 
LOADS DATA:
-----------
 
LOADS GENERATED USING PERMANENT LOAD WIZARD: NO
 
LOADS ON PRECAST
----------------
UNITS: (Point:  kips, Location: ft, Line:   klf, Trapez:   klf)
Span Beam DC/DW  Type       Mag.1   Loc.1   Mag.2   Loc.2     Description
   1    1    DC Trapez      0.064    0.00       0.064   21.25   Additional Wet Deck Overhang
   1    1    DC Line        0.068    0.00       0.068   42.50   Forms
   1    1    DC Line        0.075    0.00       0.075   42.50   Walkway DL
   1    1    DC Trapez      0.726    0.00       0.726   21.25   Wet Deck
   1    1    DC Trapez      0.014    0.00       0.014   21.25   Haunch
   1    1    DW Trapez      0.342   21.25       0.342   42.50   LL on Beam
   1    1    DW Line        0.117    0.00       0.117   42.50   LL on Walkway
   1    1    DW Point       2.350   19.25      -         -      Screed machine load 1
   1    1    DW Point       2.350   21.25      -         -      Screed machine load 2
   1    1    DW Point       2.350   25.25      -         -      Screed machine load 3
   1    1    DW Point       2.350   27.25      -         -      Screed machine load 4
 
DIAPHRAGM LOADS
---------------
UNITS: (Load:  kips, Location: ft)
Span Beam         Load Location
   1    1        0.143   21.250
   1    2        0.285   21.250
   1    3        0.285   21.250
   1    4        0.285   21.250
   1    5        0.143   21.250
 
LOADS ON COMPOSITE
------------------
UNITS: (Point:  kips, Location: ft, Line:   klf, Trapez:   klf)
       (Area:   ksf, Width: ft)
 
TEMPERATURE LOADS
-----------------
 
LIVE LOADS
----------
Live load deflection: not included.
ID: Design Lane - not incl. (Type: Design Lane)
ID: Design Tandem - not incl. (Type: Design Tandem)
ID: Design Truck - not incl. (Type: Design Truck)
 
Pedestrian Load - NONE
 

ANALYSIS DATA:
--------------
ANALYSIS PARAMETERS DATA
------------------------
 
  Truck impact:       1.330 
  Lane  impact:       1.000 
  Strength II impact: 1.330 
  Fatigue impact:     1.150 
 
 
DISTRIBUTION FACTORS (Art. 4.6.2.2):
------------------------------------
 
  Include sacrificial deck thick in ts:   NO   
  Is Span Post-tensioned:                 NO   
  ADTT (Average Daily Truck Traffic)    : 5000 
  Percent of the specified force effect : 1.00 
  Apply reduction of Moment for skew:     NO   
 
NOTE: Beam specific dead and live load DFs are printed in beam level reports.
 
LOAD FACTORS: (Table 3.4.1-1 & 3.4.1-2)
---------------------------------------
 
               Live DC(max) DC(min) DW(max) DW(min) 
----------------------------------------------------
  Service I:   1.00    1.00    1.00    1.00    1.00 
  Service III: 0.80    1.00    1.00    1.00    1.00 
  Strength I:  1.75    1.25    0.90    1.50    0.65 
 
 
----------
 
  Ductility Factor:  1.00 
  Redundancy Factor: 1.00 
  Importance Factor: 1.00 
 
----------------------------------------------------------------------------------------------------


PROJECT PARAMETERS DATA:
------------------------
MULTIPLIERS:
------------
 
  Trans len mult: Bonded   = 1.00 
                  Debonded = 1.00 
  Dev len mult:   Bonded   = 1.60 
                  Debonded = 2.00 
 
Camber & Deflection Multiplier (PCI ref.)
-----------------------------------------
 
                 Erection Final 
--------------------------------
  Prestress:         1.80  2.45 
  Self. Wt:          1.85  2.70 
  Deck + Haunch:           2.30 
  Diaphragm:               3.00 
  DL-Prec.:                3.00 
  DL-Comp.:                3.00 
 
MOMENT AND SHEAR PROVISIONS:
----------------------------
 
  Ultimate Moment Capacity, Mu-prvd computed:    AASHTO equations 
  Horizontal Shear, Beam and Slab effects in Vu: EXCLUDED         
 
STRESS LIMITS (Art. 5.9.2):
---------------------------
STRESS LIMITS AT RELEASE BEFORE LOSSES:
---------------------------------------
 
                     PRECAST     
---------------------------------
  Strength              4.50 ksi 
  Elasticity          4066.8 ksi 
  Max comp              2.92 ksi 
  Max tens             -0.19 ksi 
  Max tens,  w/reinf   -0.51 ksi 
 
STRESS LIMITS AT FINAL AFTER LOSSES:
------------------------------------
 
             PRECAST       DECK      
-------------------------------------
  Strength      5.00 ksi    4.00 ksi 
  Elasticity 4286.83 ksi 4266.22 ksi 
 
STRESS LIMITS AT FINAL 1 (P/S + DL + LL):
-----------------------------------------
 
           PRECAST     DECK     
--------------------------------
  Max comp    3.00 ksi 2.40 ksi 
 
STRESS LIMITS AT FINAL 2 (P/S + DL):
------------------------------------
 
           PRECAST     DECK     
--------------------------------
  Max comp    2.25 ksi 1.80 ksi 
 
FATIGUE I STRESS LIMITS AT FINAL 3 ( 50% P/S + 50% DL + F_LL ) (Art. 5.5.3.1):
------------------------------------------------------------------------------
 
           PRECAST     DECK     
--------------------------------
  Max comp    2.00 ksi   -  ksi 
 
SERVICE III (Tension):
----------------------
 
           PRECAST      DECK     
---------------------------------
  Max tens   -0.00 ksi -0.38 ksi 
 
RESISTANCE FACTORS (Art. 5.5.4.2):
----------------------------------
 
  Flexure Reinforced                   
  Compression controlled sections 0.75 
  Tension controlled sections     0.90 
                                       
  Flexure Prestressed                  
  Compression controlled sections 0.75 
  Tension controlled sections     1.00 
                                       
  Shear                           0.90 
 
PRESTRESS LOSSES:
-----------------
 
  Time Dependent Losses, Approximate Method (Art.5.9.3.3) 
  Days to release = 0.75                                  
  Rel. Humid.(RH) = 70.0 %                                
 
----------------------------------------------------------------------------------------------------


RATING PARAMETERS
-----------------
 
 
                  Rating Factors                     References     Values 
---------------------------------------------------------------------------
  Condition Factor                               Table 6A.4.2.3-1     1.00 
  System Factor for Flexural Effect              Table 6A.4.2.4-1     1.00 
  System Factor for Shear Effect                 Art. 6A.4.2.4        1.00 
  ADTT                                           Section C3.6.1.1.2   5000 
  Dynamic Load Factor for Design Level           Art. 6A.4.3.3        0.33 
  Dynamic Load Factor for Legal and Permit Level Table C6A.4.4.3-1    0.33 
 
For Flexural Effect: Condition Factor * System Factor = 1.00 >= 0.85 (Art. 6A.4.2.1) OK
For Shear Effect: Condition Factor * System Factor = 1.00 >= 0.85 (Art. 6A.4.2.1 and 6A.4.2.4) OK
 
Dead Load Factors (Table 6A.4.2.2-1)
------------------------------------
  Limit State  DC   DW  
------------------------
  Strength I  1.25 1.50 
  Strength II 1.25 1.50 
  Service I   1.00 1.00 
  Service III 1.00 1.00 
 
----------------------------------------------------------------------------------------------------


 
BEAM SPECIFIC MATERIAL PROPERTIES:
 
   Span#, Beam#      Tendon-ID     Girder-f'ci Girder-f'c Deck-f'c 
                                       ksi         ksi       ksi   
-------------------------------------------------------------------
  Span:1, Beam:1 0.6''-LL-270-72.6    4.50        5.00      4.00   
  Span:1, Beam:2 0.6''-LL-270-72.6    4.50        5.00      4.00   
  Span:1, Beam:3 0.6''-LL-270-72.6    4.50        5.00      4.00   
  Span:1, Beam:4 0.6''-LL-270-72.6    4.50        5.00      4.00   
  Span:1, Beam:5 0.6''-LL-270-72.6    4.50        5.00      4.00   
 
 
Span:1, Beam:1
 
PRESTRESSED STEEL:
 10 strands, 0.6''-LL-270-72.6, Low relaxation strands
Straight Pattern
 
END PATTERN (Ycg = 9.80 in):
 
  5 @  2.000 in 3 @  6.000 in 1 @ 34.000 in 1 @ 36.000 in 
 
REINFORCING STEEL:
 
  Tension steel:     
---------------------
  fy        60.0 ksi 
  Es       29000 ksi 
 
Stirrups:
 
  # legs    Size     fy   Area Spacing  Start    End    Extends  
                   (ksi) (in2)   (in)    (ft)    (ft)  into Deck 
-----------------------------------------------------------------
       2 US#4[M13]  60.0  0.40    9.00  0.1457  2.3960 Yes       
       2 US#5[M16]  60.0  0.62    3.00  0.3960  0.6460 No        
       2 US#5[M16]  60.0  0.62    7.50  0.6460  1.2710 No        
       2 US#5[M16]  60.0  0.62    9.00  1.2710  2.0210 No        
       2 US#5[M16]  60.0  0.62    9.88  2.0210  2.8501 No        
       2 US#4[M13]  60.0  0.40   10.75  2.3960  3.2920 Yes       
       2 US#5[M16]  60.0  0.62   10.87  2.8501  3.7598 No        
       2 US#4[M13]  60.0  0.40   11.00  3.2920  4.2100 Yes       
       2 US#5[M16]  60.0  0.62   11.76  3.7598  4.7402 No        
       2 US#4[M13]  60.0  0.40   12.50  4.2080  6.2920 Yes       
       2 US#5[M16]  60.0  0.62   12.48  4.7402  5.7900 No        
       2 US#5[M16]  60.0  0.62   13.80  5.7900  6.9501 No        
       2 US#5[M16]  60.0  0.62   15.00  6.9501 11.9501 No        
       2 US#4[M13]  60.0  0.40   15.00  6.2920 12.5420 Yes       
       2 US#4[M13]  60.0  0.40   17.00 12.5420 21.0420 Yes       
       2 US#4[M13]  60.0  0.40    8.52 21.0420 22.4580 Yes       
       2 US#4[M13]  60.0  0.40   17.00 22.4580 30.9580 Yes       
       2 US#4[M13]  60.0  0.40   15.00 30.9580 37.2080 Yes       
       2 US#5[M16]  60.0  0.62   15.00 31.5499 36.5499 No        
       2 US#5[M16]  60.0  0.62   13.80 36.5499 37.7100 No        
       2 US#5[M16]  60.0  0.62   12.48 37.7100 38.7598 No        
       2 US#4[M13]  60.0  0.40   12.50 37.2080 39.2920 Yes       
       2 US#5[M16]  60.0  0.62   11.76 38.7598 39.7402 No        
       2 US#4[M13]  60.0  0.40   11.00 39.2900 40.2080 Yes       
       2 US#5[M16]  60.0  0.62   10.87 39.7402 40.6499 No        
       2 US#4[M13]  60.0  0.40   10.75 40.2080 41.1040 Yes       
       2 US#5[M16]  60.0  0.62    9.88 40.6499 41.4790 No        
       2 US#5[M16]  60.0  0.62    9.00 41.4790 42.2290 No        
       2 US#5[M16]  60.0  0.62    7.50 42.2290 42.8540 No        
       2 US#5[M16]  60.0  0.62    3.00 42.8540 43.1040 No        
       2 US#4[M13]  60.0  0.40    9.00 41.1040 43.3543 Yes       
 
Top Steel:
 
  #bars    Size   Dist. from Top  Area  Start   End   Side Cover 
                       (in)      (in2)  (ft)    (ft)     (in)    
-----------------------------------------------------------------
      2 US#6[M19]           2.00 0.880 0.1458 43.1670       3.00 
 
Bottom Steel:
 
  #bars Size Dist. from Top  Area Start  End Side Cover 
                  (in)      (in2)  (ft) (ft)    (in)    
--------------------------------------------------------
 
 
Span:1, Beam:2
 
PRESTRESSED STEEL:
No strands, 0.6''-LL-270-72.6, Low relaxation
 
REINFORCING STEEL:
 
  Tension /Shear steel: 
------------------------
  fy        60.0 ksi    
  Es       29000 ksi    
 
 
Span:1, Beam:3
 
PRESTRESSED STEEL:
No strands, 0.6''-LL-270-72.6, Low relaxation
 
REINFORCING STEEL:
 
  Tension /Shear steel: 
------------------------
  fy        60.0 ksi    
  Es       29000 ksi    
 
 
Span:1, Beam:4
 
PRESTRESSED STEEL:
No strands, 0.6''-LL-270-72.6, Low relaxation
 
REINFORCING STEEL:
 
  Tension /Shear steel: 
------------------------
  fy        60.0 ksi    
  Es       29000 ksi    
 
 
Span:1, Beam:5
 
PRESTRESSED STEEL:
No strands, 0.6''-LL-270-72.6, Low relaxation
 
REINFORCING STEEL:
 
  Tension /Shear steel: 
------------------------
  fy        60.0 ksi    
  Es       29000 ksi    
 

Span: 1, Beam: 1
 
PRECAST DATA:                                    GENERAL BRIDGE DATA:
-------------                                    --------------------
Section Id: IA-Std-B                            Bridge Width       =  36.33 ft
Type      : I-Girder                            Curb-to-curb       =  36.33 ft
Flng width: Top = 13.000 in    Bot = 17.000 in  Beam Spac. Lt./Rt. =   3.17/  7.50 ft
     thick: Top =  5.000 in    Bot =  7.000 in  Lane width         =  12.00 ft
Stems     : No  =  1                            Number of lanes    =   3
            Top =  6.000 in                     Interior/Exterior  =   Exterior
            Bot =  6.000 in                     Start Skew Angle   =   0.00 degrees
                                                End Skew Angle     =   0.00 degrees
Shear width     =  6.000 in                     
Minimum Thickness Criteria, Article 5.12.3.2 checked: OK.
 
TOPPING DATA:
-------------
Effective Deck Thickness   =   0.000 in
Sacrificial Deck Thickness   =   0.000 in
Haunch:
       Thickness =   0.000 in
       Width     =   0.000 in
Effective width  =  83.004 in (Art. 4.6.2.6.1)
 
GENERAL LOAD DATA:
------------------
Dead loads on precast:
---------------------
UNITS: (Point:  kips, Location: ft, Line:   klf, Trapez:   klf)
  DC/DW    Type     Mag.1     Loc.1    Mag.2     Loc.2
     DC  Trapez     0.064      0.00       0.064   21.25
     DC  Line       0.068      0.00       0.068   42.50
     DC  Line       0.075      0.00       0.075   42.50
     DC  Trapez     0.726      0.00       0.726   21.25
     DC  Trapez     0.014      0.00       0.014   21.25
     DW  Trapez     0.342     21.25       0.342   42.50
     DW  Line       0.117      0.00       0.117   42.50
     DW  Point      2.350     19.25      -         -   
     DW  Point      2.350     21.25      -         -   
     DW  Point      2.350     25.25      -         -   
     DW  Point      2.350     27.25      -         -   
 
Diaphragm loads: kips, ft
      Mag.      Loc.
      0.14    21.25 
 
Dead loads on composite: See Project info for composite loads
 
GENERAL SPAN DATA:
------------------
Overall length = 43.500 ft
Release length = 43.500 ft
Design  length = 42.500 ft
 
Kern points:
------------
Upper    =   26.56 in
Lower    =    9.67 in
 
DISTRIBUTION FACTORS (Art. 4.6.2.2):
------------------------------------
Type j, connected only enough to prevent relative vertical displacement
 
Live Moment (2+ lanes loaded)  : 0.907   (Calculated) (#)
Live Moment (1  lane  loaded)  : 0.907   (Calculated) (#)
Live Shear  (2+ lanes loaded)  : 0.907   (Calculated) (#)
Live Shear  (1  lane  loaded)  : 0.907   (Calculated) (#)
(#) Lever rule (C4.6.2.2.1)
The LL distribution computation is using the effective slab depth (ts = 0.00in).
Include sacrificial deck thick in ts:  NO
 
Dead Loads and Pedestrian Load distributed equally to all beams (Art. 4.6.2.2.1)
 
Pedestrian : 0.200   (Calculated)
 
Comp.  DC  : 0.200   (Calculated)
Comp.  DW  : 0.200   (Calculated)
 
RESISTANCE FACTORS (Art. 5.5.4.2):
----------------------------------
Flexure Reinforced:
   Compression controlled sections : 0.75
   Tension controlled sections     : 0.90
Flexure Prestressed:
   Compression controlled sections : 0.75
   Tension controlled sections     : 1.00
Shear                              : 0.90
 

Span: 1, Beam: 1
 
SECTION PROPERTIES:
-------------------
                             PRECAST          COMPOSITE
                             -------          ---------
Area                  =        382.5 in2            382.5 in2#
Total Height          =        39.00 in             39.00 in  
Mom. of Inertia (Ixx) =        62000 in4            62000 in4#
Ht. of c.g.           =        17.06 in             17.06 in#
Density               =       150.00 pcf           150.00 pcf
Lambda                =         1.00                 1.00 
Self-weight           =        398.4 plf            398.4 plf   
Mom. of Inertia (Iyy) =       5157.0 in4   
Poisson's Ratio       =          0.2
Thermal coeff.        =  0.000006000 1/F  
 
(#) Of Total Section using Ect/Ec = 0.9952

NOTE: Poisson's ratio may be assumed as 0.2 for lightweight concrete with specified compressive strengths
up to  10.0 ksi and for normal weight concrete with specified compressive strengths up to 15.0 ksi.

Use transformed strand and rebar: Strand Only
 
TRANSFORMED SECTION PROPERTIES:  
                 Bearing    Trans      H/2    0.10L    0.20L    0.30L    0.40L  Midspan
  Location,  ft     0.00     2.50     1.63     3.85     8.20    12.55    16.90    21.25
 
Precast: (At Release, using Ec =  4066.8 ksi )
  Area    , in2    384.7    395.5    391.7    395.5    395.5    395.5    395.5    395.5
  Yb      ,  in    17.02    16.82    16.89    16.82    16.82    16.82    16.82    16.82
  MI(Ixx) , in4    62114    62665    62475    62665    62665    62665    62665    62665
Composite: (At Final, using Ec =  4286.8 ksi )
  Area    , in2    384.5    394.8    391.2    394.8    394.8    394.8    394.8    394.8
  Yb      ,  in    17.02    16.83    16.90    16.83    16.83    16.83    16.83    16.83
  MI(Ixx) , in4    62107    62626    62447    62626    62626    62626    62626    62626

Span: 1, Beam: 1
 
STRESS LIMITS (Art. 5.9.2):
--------------------------
 
                            PRECAST               DECK
                            -------               ----
STRESS LIMITS AT RELEASE BEFORE LOSSES:
  Strength           =       4.50  ksi   
  Elasticity         =     4066.8 ksi   
  Max comp           =       2.93 ksi   
  Max tens           =      -0.19 ksi   
  Max tens,w/reinf   =      -0.51 ksi   
 
STRESS LIMITS AT FINAL AFTER LOSSES:
  Strength           =       5.00 ksi           4.00 ksi
  Elasticity         =    4286.83 ksi        4266.22 ksi
 
STRESS LIMITS AT FINAL 1 (P/S + DL + LL):
  Max comp           =       3.00 ksi           2.40 ksi
 
STRESS LIMITS AT FINAL 2 (P/S + DL):
  Max comp           =       2.25 ksi           1.80 ksi
 
FATIGUE I STRESS LIMITS AT FINAL 3 ( 50% P/S + 50% DL + F_LL ) (Art. 5.5.3.1):
  Max comp           =       2.00 ksi           1.60 ksi
 
SERVICE III (Tension):
  Max tens           =      -0.00 ksi          -0.38 ksi
 
 

Span: 1, Beam: 1
 
PRESTRESSED STEEL:  10 strands, 0.6''-LL-270-72.6, Low relaxation strands
Straight Pattern
END PATTERN (Ycg = 9.80 in):
     5 @  2.000 in     3 @  6.000 in     1 @ 34.000 in     1 @ 36.000 in
 
Strand Diameter       =    0.60 in       Tensile Strength(fpu) =      270.0 ksi
Strand Area           =    0.22 in2      Initial Prestress     =  0.73 fpu =   196.0 ksi
Total Strand Area     =    2.17 in2      Initial Pull          =      425.4 kips 
Trans. Len,bonded     =   3.000 ft       Dev. Len, bonded      =      9.033 ft
Trans. Len,debonded   =   3.000 ft       Dev. Len, debonded    =     11.291 ft
Holddown Force        =   0.000 kips     Beam Shrtng (PL/AE)   =      0.139 in
 
 
Span: 1, Beam: 1
 
ESTIMATED QUANTITIES
 
  Prestressing   Strands               Beam    Concrete  Stirrups  Longitudinal Bars 
   (linear ft) (LB/1000ft)   (LB)   Vol(C.Y.)   Wt(LB)     (LB)           (LB)       
-------------------------------------------------------------------------------------
       435.000         740 321.900      4.280 17332.068   349.258     128.840        
 
 
REINFORCING STEEL: Tension steel: fy = 60.0 ksi Es =  29000 ksi
Stirrups:
    # legs     Size          fy         Area      Spacing       Start       End     Extends
                            (ksi)       (in2)       (in)         (ft)       (ft)    into Deck
   -------  ----------    --------    --------    --------     --------   --------- ----------
      2      US#4[M13]       60.00        0.40       9.00       0.1457      2.3960    Yes
      2      US#5[M16]       60.00        0.62       3.00       0.3960      0.6460     No
      2      US#5[M16]       60.00        0.62       7.50       0.6460      1.2710     No
      2      US#5[M16]       60.00        0.62       9.00       1.2710      2.0210     No
      2      US#5[M16]       60.00        0.62       9.88       2.0210      2.8501     No
      2      US#4[M13]       60.00        0.40      10.75       2.3960      3.2920    Yes
      2      US#5[M16]       60.00        0.62      10.87       2.8501      3.7598     No
      2      US#4[M13]       60.00        0.40      11.00       3.2920      4.2100    Yes
      2      US#5[M16]       60.00        0.62      11.76       3.7598      4.7402     No
      2      US#4[M13]       60.00        0.40      12.50       4.2080      6.2920    Yes
      2      US#5[M16]       60.00        0.62      12.48       4.7402      5.7900     No
      2      US#5[M16]       60.00        0.62      13.80       5.7900      6.9501     No
      2      US#5[M16]       60.00        0.62      15.00       6.9501     11.9501     No
      2      US#4[M13]       60.00        0.40      15.00       6.2920     12.5420    Yes
      2      US#4[M13]       60.00        0.40      17.00      12.5420     21.0420    Yes
      2      US#4[M13]       60.00        0.40       8.52      21.0420     22.4580    Yes
      2      US#4[M13]       60.00        0.40      17.00      22.4580     30.9580    Yes
      2      US#4[M13]       60.00        0.40      15.00      30.9580     37.2080    Yes
      2      US#5[M16]       60.00        0.62      15.00      31.5499     36.5499     No
      2      US#5[M16]       60.00        0.62      13.80      36.5499     37.7100     No
      2      US#5[M16]       60.00        0.62      12.48      37.7100     38.7598     No
      2      US#4[M13]       60.00        0.40      12.50      37.2080     39.2920    Yes
      2      US#5[M16]       60.00        0.62      11.76      38.7598     39.7402     No
      2      US#4[M13]       60.00        0.40      11.00      39.2900     40.2080    Yes
      2      US#5[M16]       60.00        0.62      10.87      39.7402     40.6499     No
      2      US#4[M13]       60.00        0.40      10.75      40.2080     41.1040    Yes
      2      US#5[M16]       60.00        0.62       9.88      40.6499     41.4790     No
      2      US#5[M16]       60.00        0.62       9.00      41.4790     42.2290     No
      2      US#5[M16]       60.00        0.62       7.50      42.2290     42.8540     No
      2      US#5[M16]       60.00        0.62       3.00      42.8540     43.1040     No
      2      US#4[M13]       60.00        0.40       9.00      41.1040     43.3543    Yes
 
Top Steel:
 
  #bars    Size   Dist. from Top  Area  Start   End   Side Cover 
                       (in)      (in2)  (ft)    (ft)     (in)    
-----------------------------------------------------------------
      2 US#6[M19]           2.00 0.880 0.1458 43.1670       3.00 
 
 
Bottom Steel:
 
  #bars Size Dist. from Top  Area Start  End Side Cover 
                  (in)      (in2)  (ft) (ft)    (in)    
--------------------------------------------------------
 
---------------------------------------------------------------------------------------
Midspan: Str. area = 2.1700 in2       Ycg =  9.80 in
         P_init    =      425.4 kips  Ecc =  7.26 in
Days to release = 0.75  Rel. Humid.(RH) = 70.0 % Es = 28500.0 ksi  Eci =   4067 ksi
 
 
AASHTO LOSSES
Elastic Shortening     **     8.60 ksi  (Eq 5.9.5.2.3a-1), (fcgp= 1.227 ksi)
Elastic Gains                                                Gains       Adjustment
    due to Precast Loads                                   -2.46 ksi    0.00 ksi
    due to Composite Loads                                 -0.00 ksi    0.00 ksi
    due to Live Loads                                      -0.00 ksi    0.00 ksi
 
Time Dependent Losses (Approximate Method (Art.5.9.3.3))
                            Initial                            Final
 
Steel relaxation           0.00 ksi                         2.40 ksi (Eq 5.9.3.3-1)
Concrete shrinkage         0.00 ksi                        10.91 ksi (Eq 5.9.3.3-1)
Concrete creep             0.00 ksi                        10.11 ksi (Eq 5.9.3.3-1)
                       ------------                    ------------
Sub-total                  8.60 ksi  ( 4.39 %)            20.96 ksi (10.69 %)
Total Prestress Losses                                    29.56 ksi (15.08 %)
 
Prestressing Stress Limit Check (Table 5.9.3.1)
     initial fpi = 196.0 ksi < 0.75 fpu, OK 
     initial fpe = 166.5 ksi < 0.80 fpy, OK 
 
 
** Since the transformed section properties option has been selected, even though ES losses
have been calculated explicitly here, they are not included as a part of stress calculations.
Please see theory section for complete explanation.
 
---------------------------------------------------------------------------------------

 
SHEAR AND MOMENT ENVELOPE : Span : 1, Beam : 1, SERVICE I
Shears: kips, Moments: kft
 
                Bearing   Trans     H/2   0.10L   0.20L   0.30L   0.40L Midspan
Location,   ft     0.00    2.50    1.63    3.85    8.20   12.55   16.90   21.25
Self wt.  : M       0.0    19.9    13.2    29.6    56.0    74.9    86.2    90.0
(Max)       V       8.5     7.5     7.8     6.9     5.2     3.5     1.7     0.0
DL-Prec.  : M       0.0    36.6    24.5    54.0    98.1   124.3   132.5   122.9
DC(Max)     V      15.8    13.5    14.3    12.2     8.1     4.0     0.2     4.3
DL-Prec.  : M       0.0    21.0    13.7    32.1    66.2    98.2   127.9   150.7
DW(Max)     V       8.6     8.3     8.4     8.1     7.6     7.1     6.6     3.7
Deck +    : M       0.0     0.0     0.0     0.0     0.0     0.0     0.0     0.0
Haunch (Max)V       0.0     0.0     0.0     0.0     0.0     0.0     0.0     0.0
Diaphragm : M       0.0     0.2     0.1     0.3     0.6     0.9     1.2     1.5
(Max)       V       0.1     0.1     0.1     0.1     0.1     0.1     0.1     0.1
DL-Comp   : M       0.0     0.0     0.0     0.0     0.0     0.0     0.0     0.0
DC(Max)     V       0.0     0.0     0.0     0.0     0.0     0.0     0.0     0.0
DL-Comp   : M       0.0     0.0     0.0     0.0     0.0     0.0     0.0     0.0
DW(Max)     V       0.0     0.0     0.0     0.0     0.0     0.0     0.0     0.0
LL + I    : M+      0.0     0.0     0.0     0.0     0.0     0.0     0.0     0.0
            V       0.0     0.0     0.0     0.0     0.0     0.0     0.0     0.0
LL + I    : M-      0.0     0.0     0.0     0.0     0.0     0.0     0.0     0.0
            V       0.0     0.0     0.0     0.0     0.0     0.0     0.0     0.0
LL + I    : Vmx     0.0     0.0     0.0     0.0     0.0     0.0     0.0     0.0
            M       0.0     0.0     0.0     0.0     0.0     0.0     0.0     0.0
Total     : M+      0.0    77.8    51.6   115.9   220.9   298.2   347.8   365.1
            V      32.9    29.3    30.6    27.3    20.9    14.6     8.5     8.1
Total     : M-      0.0     0.0     0.0     0.0     0.0     0.0     0.0     0.0
            V       0.0     0.0     0.0     0.0     0.0     0.0     0.0     0.0
Total     : Vmx    32.9    29.3    30.6    27.3    20.9    14.6     8.5     8.1
            M       0.0    77.8    51.6   115.9   220.9   298.2   347.8   365.1
 
                  0.60L   0.70L   0.80L   0.90L     H/2   Trans Bearing
Location,   ft    25.60   29.95   34.30   38.65   40.88   40.00   42.50
Self wt.  : M      86.2    74.9    56.0    29.6    13.2    19.9     0.0
(Max)       V       1.7     3.5     5.2     6.9     7.8     7.5     8.5
DL-Prec.  : M     103.0    80.4    55.1    27.1    11.7    17.8     0.0
DC(Max)     V       4.9     5.5     6.1     6.8     7.1     6.9     7.3
DL-Prec.  : M     151.5   127.9    91.8    46.9    20.6    31.2     0.0
DW(Max)     V       3.0     7.3     9.3    11.3    12.3    11.9    13.1
Deck +    : M       0.0     0.0     0.0     0.0     0.0     0.0     0.0
Haunch (Max)V       0.0     0.0     0.0     0.0     0.0     0.0     0.0
Diaphragm : M       1.2     0.9     0.6     0.3     0.1     0.2     0.0
(Max)       V       0.1     0.1     0.1     0.1     0.1     0.1     0.1
DL-Comp   : M       0.0     0.0     0.0     0.0     0.0     0.0     0.0
DC(Max)     V       0.0     0.0     0.0     0.0     0.0     0.0     0.0
DL-Comp   : M       0.0     0.0     0.0     0.0     0.0     0.0     0.0
DW(Max)     V       0.0     0.0     0.0     0.0     0.0     0.0     0.0
LL + I    : M+      0.0     0.0     0.0     0.0     0.0     0.0     0.0
            V       0.0     0.0     0.0     0.0     0.0     0.0     0.0
LL + I    : M-      0.0     0.0     0.0     0.0     0.0     0.0     0.0
            V       0.0     0.0     0.0     0.0     0.0     0.0     0.0
LL + I    : Vmx     0.0     0.0     0.0     0.0     0.0     0.0     0.0
            M       0.0     0.0     0.0     0.0     0.0     0.0     0.0
Total     : M+    342.0   284.1   203.5   103.9    45.7    69.2     0.0
            V       9.7    16.4    20.7    25.1    27.3    26.4    28.9
Total     : M-      0.0     0.0     0.0     0.0     0.0     0.0     0.0
            V       0.0     0.0     0.0     0.0     0.0     0.0     0.0
Total     : Vmx     9.7    16.4    20.7    25.1    27.3    26.4    28.9
            M     342.0   284.1   203.5   103.9    45.7    69.2     0.0
 

 
REACTIONS (kips), SERVICE I
---------
 
Load Type          Left Support     Right Support
---------          ------------     -------------
Self Wt.                8.5              8.5
Deck+Haunch             0.0              0.0
Diaphragm               0.1              0.1
DL-Prec.(DC)           15.8              7.3
DL-Prec.(DW)            8.6             13.1
DL-Comp.(DC)            0.0              0.0
DL-Comp.(DW)            0.0              0.0
Live                    0.0              0.0
        Truck           0.0              0.0
        Lane            0.0              0.0
Pedestrian              0.0              0.0
 
Upward reactions are positive.
Live Load reactions are per lane with no distribution factor and no impact.
Reactions are not multiplied by Load Modifiers (ductility, redundancy and operational importance).
Non-composite load types are per beam.
Composite and Pedestrian load types are per total bridge width.

 
SHEAR AND MOMENT ENVELOPE : Span : 1, Beam : 1, SERVICE III
Shears: kips, Moments: kft
 
                Bearing   Trans     H/2   0.10L   0.20L   0.30L   0.40L Midspan
Location,   ft     0.00    2.50    1.63    3.85    8.20   12.55   16.90   21.25
Self wt.  : M       0.0    19.9    13.2    29.6    56.0    74.9    86.2    90.0
(Max)       V       8.5     7.5     7.8     6.9     5.2     3.5     1.7     0.0
DL-Prec.  : M       0.0    36.6    24.5    54.0    98.1   124.3   132.5   122.9
DC(Max)     V      15.8    13.5    14.3    12.2     8.1     4.0     0.2     4.3
DL-Prec.  : M       0.0    21.0    13.7    32.1    66.2    98.2   127.9   150.7
DW(Max)     V       8.6     8.3     8.4     8.1     7.6     7.1     6.6     3.7
Deck +    : M       0.0     0.0     0.0     0.0     0.0     0.0     0.0     0.0
Haunch (Max)V       0.0     0.0     0.0     0.0     0.0     0.0     0.0     0.0
Diaphragm : M       0.0     0.2     0.1     0.3     0.6     0.9     1.2     1.5
(Max)       V       0.1     0.1     0.1     0.1     0.1     0.1     0.1     0.1
DL-Comp   : M       0.0     0.0     0.0     0.0     0.0     0.0     0.0     0.0
DC(Max)     V       0.0     0.0     0.0     0.0     0.0     0.0     0.0     0.0
DL-Comp   : M       0.0     0.0     0.0     0.0     0.0     0.0     0.0     0.0
DW(Max)     V       0.0     0.0     0.0     0.0     0.0     0.0     0.0     0.0
LL + I    : M+      0.0     0.0     0.0     0.0     0.0     0.0     0.0     0.0
            V       0.0     0.0     0.0     0.0     0.0     0.0     0.0     0.0
LL + I    : M-      0.0     0.0     0.0     0.0     0.0     0.0     0.0     0.0
            V       0.0     0.0     0.0     0.0     0.0     0.0     0.0     0.0
LL + I    : Vmx     0.0     0.0     0.0     0.0     0.0     0.0     0.0     0.0
            M       0.0     0.0     0.0     0.0     0.0     0.0     0.0     0.0
Total     : M+      0.0    77.8    51.6   115.9   220.9   298.2   347.8   365.1
            V      32.9    29.3    30.6    27.3    20.9    14.6     8.5     8.1
Total     : M-      0.0     0.0     0.0     0.0     0.0     0.0     0.0     0.0
            V       0.0     0.0     0.0     0.0     0.0     0.0     0.0     0.0
Total     : Vmx    32.9    29.3    30.6    27.3    20.9    14.6     8.5     8.1
            M       0.0    77.8    51.6   115.9   220.9   298.2   347.8   365.1
 
                  0.60L   0.70L   0.80L   0.90L     H/2   Trans Bearing
Location,   ft    25.60   29.95   34.30   38.65   40.88   40.00   42.50
Self wt.  : M      86.2    74.9    56.0    29.6    13.2    19.9     0.0
(Max)       V       1.7     3.5     5.2     6.9     7.8     7.5     8.5
DL-Prec.  : M     103.0    80.4    55.1    27.1    11.7    17.8     0.0
DC(Max)     V       4.9     5.5     6.1     6.8     7.1     6.9     7.3
DL-Prec.  : M     151.5   127.9    91.8    46.9    20.6    31.2     0.0
DW(Max)     V       3.0     7.3     9.3    11.3    12.3    11.9    13.1
Deck +    : M       0.0     0.0     0.0     0.0     0.0     0.0     0.0
Haunch (Max)V       0.0     0.0     0.0     0.0     0.0     0.0     0.0
Diaphragm : M       1.2     0.9     0.6     0.3     0.1     0.2     0.0
(Max)       V       0.1     0.1     0.1     0.1     0.1     0.1     0.1
DL-Comp   : M       0.0     0.0     0.0     0.0     0.0     0.0     0.0
DC(Max)     V       0.0     0.0     0.0     0.0     0.0     0.0     0.0
DL-Comp   : M       0.0     0.0     0.0     0.0     0.0     0.0     0.0
DW(Max)     V       0.0     0.0     0.0     0.0     0.0     0.0     0.0
LL + I    : M+      0.0     0.0     0.0     0.0     0.0     0.0     0.0
            V       0.0     0.0     0.0     0.0     0.0     0.0     0.0
LL + I    : M-      0.0     0.0     0.0     0.0     0.0     0.0     0.0
            V       0.0     0.0     0.0     0.0     0.0     0.0     0.0
LL + I    : Vmx     0.0     0.0     0.0     0.0     0.0     0.0     0.0
            M       0.0     0.0     0.0     0.0     0.0     0.0     0.0
Total     : M+    342.0   284.1   203.5   103.9    45.7    69.2     0.0
            V       9.7    16.4    20.7    25.1    27.3    26.4    28.9
Total     : M-      0.0     0.0     0.0     0.0     0.0     0.0     0.0
            V       0.0     0.0     0.0     0.0     0.0     0.0     0.0
Total     : Vmx     9.7    16.4    20.7    25.1    27.3    26.4    28.9
            M     342.0   284.1   203.5   103.9    45.7    69.2     0.0
 


 
SHEAR AND MOMENT ENVELOPE : Span : 1, Beam : 1, STRENGTH I
Shears: kips, Moments: kft
 
                Bearing   Trans     H/2   0.10L   0.20L   0.30L   0.40L Midspan
Location,   ft     0.00    2.50    1.63    3.85    8.20   12.55   16.90   21.25
Self wt.  : M       0.0    24.9    16.5    37.1    70.0    93.6   107.7   112.4
(Max)       V      10.6     9.3     9.8     8.7     6.5     4.3     2.2     0.0
Self wt.  : M       0.0    17.9    11.9    26.7    50.4    67.4    77.6    81.0
(Min)       V       7.6     6.7     7.0     6.2     4.7     3.1     1.6     0.0
DL-Prec.  : M       0.0    45.8    30.6    67.4   122.6   155.3   165.7   153.7
DC(Max)     V      19.8    16.8    17.9    15.2    10.1     5.0     0.2     5.3
DL-Prec.  : M       0.0    33.0    22.0    48.6    88.2   111.8   119.3   110.6
DC(Min)     V      14.3    12.1    12.9    11.0     7.3     3.6     0.1     3.8
DL-Prec.  : M       0.0    31.5    20.6    48.1    99.3   147.3   191.9   226.1
DW(Max)     V      12.8    12.4    12.5    12.2    11.4    10.6     9.9     5.6
DL-Prec.  : M       0.0    13.7     8.9    20.8    43.0    63.8    83.1    98.0
DW(Min)     V       5.6     5.4     5.4     5.3     4.9     4.6     4.3     2.4
Deck +    : M       0.0     0.0     0.0     0.0     0.0     0.0     0.0     0.0
Haunch (Max)V       0.0     0.0     0.0     0.0     0.0     0.0     0.0     0.0
Deck +    : M       0.0     0.0     0.0     0.0     0.0     0.0     0.0     0.0
Haunch (Min)V       0.0     0.0     0.0     0.0     0.0     0.0     0.0     0.0
Diaphragm : M       0.0     0.2     0.1     0.3     0.7     1.1     1.5     1.9
(Max)       V       0.1     0.1     0.1     0.1     0.1     0.1     0.1     0.1
Diaphragm : M       0.0     0.2     0.1     0.2     0.5     0.8     1.1     1.4
(Min)       V       0.1     0.1     0.1     0.1     0.1     0.1     0.1     0.1
DL-Comp   : M       0.0     0.0     0.0     0.0     0.0     0.0     0.0     0.0
DC(Max)     V       0.0     0.0     0.0     0.0     0.0     0.0     0.0     0.0
DL-Comp   : M       0.0     0.0     0.0     0.0     0.0     0.0     0.0     0.0
DC(Min)     V       0.0     0.0     0.0     0.0     0.0     0.0     0.0     0.0
DL-Comp   : M       0.0     0.0     0.0     0.0     0.0     0.0     0.0     0.0
DW(Max)     V       0.0     0.0     0.0     0.0     0.0     0.0     0.0     0.0
DL-Comp   : M       0.0     0.0     0.0     0.0     0.0     0.0     0.0     0.0
DW(Min)     V       0.0     0.0     0.0     0.0     0.0     0.0     0.0     0.0
LL + I    : M+      0.0     0.0     0.0     0.0     0.0     0.0     0.0     0.0
            V       0.0     0.0     0.0     0.0     0.0     0.0     0.0     0.0
LL + I    : M-      0.0     0.0     0.0     0.0     0.0     0.0     0.0     0.0
            V       0.0     0.0     0.0     0.0     0.0     0.0     0.0     0.0
LL + I    : Vmx     0.0     0.0     0.0     0.0     0.0     0.0     0.0     0.0
            M       0.0     0.0     0.0     0.0     0.0     0.0     0.0     0.0
Total     : M+      0.0   102.5    67.9   153.0   292.7   397.3   466.8   494.1
            V      43.3    38.7    40.3    36.2    28.1    20.0    12.3    11.0
Total     : M-      0.0     0.0     0.0     0.0     0.0     0.0     0.0     0.0
            V       0.0     0.0     0.0     0.0     0.0     0.0     0.0     0.0
Total     : Vmx    43.3    38.7    40.3    36.2    28.1    20.0    12.3    11.0
            M       0.0    84.6    56.2   125.7   236.4   313.8   358.1   366.0
 
                  0.60L   0.70L   0.80L   0.90L     H/2   Trans Bearing
Location,   ft    25.60   29.95   34.30   38.65   40.88   40.00   42.50
Self wt.  : M     107.7    93.6    70.0    37.1    16.5    24.9     0.0
(Max)       V       2.2     4.3     6.5     8.7     9.8     9.3    10.6
Self wt.  : M      77.6    67.4    50.4    26.7    11.9    17.9     0.0
(Min)       V       1.6     3.1     4.7     6.2     7.0     6.7     7.6
DL-Prec.  : M     128.8   100.5    68.9    33.8    14.6    22.3     0.0
DC(Max)     V       6.1     6.9     7.7     8.4     8.8     8.7     9.1
DL-Prec.  : M      92.7    72.4    49.6    24.4    10.5    16.0     0.0
DC(Min)     V       4.4     5.0     5.5     6.1     6.4     6.3     6.6
DL-Prec.  : M     227.3   191.9   137.7    70.4    31.0    46.9     0.0
DW(Max)     V       4.5    11.0    14.0    17.0    18.5    17.9    19.6
DL-Prec.  : M      98.5    83.2    59.7    30.5    13.4    20.3     0.0
DW(Min)     V       1.9     4.8     6.1     7.3     8.0     7.8     8.5
Deck +    : M       0.0     0.0     0.0     0.0     0.0     0.0     0.0
Haunch (Max)V       0.0     0.0     0.0     0.0     0.0     0.0     0.0
Deck +    : M       0.0     0.0     0.0     0.0     0.0     0.0     0.0
Haunch (Min)V       0.0     0.0     0.0     0.0     0.0     0.0     0.0
Diaphragm : M       1.5     1.1     0.7     0.3     0.1     0.2     0.0
(Max)       V       0.1     0.1     0.1     0.1     0.1     0.1     0.1
Diaphragm : M       1.1     0.8     0.5     0.2     0.1     0.2     0.0
(Min)       V       0.1     0.1     0.1     0.1     0.1     0.1     0.1
DL-Comp   : M       0.0     0.0     0.0     0.0     0.0     0.0     0.0
DC(Max)     V       0.0     0.0     0.0     0.0     0.0     0.0     0.0
DL-Comp   : M       0.0     0.0     0.0     0.0     0.0     0.0     0.0
DC(Min)     V       0.0     0.0     0.0     0.0     0.0     0.0     0.0
DL-Comp   : M       0.0     0.0     0.0     0.0     0.0     0.0     0.0
DW(Max)     V       0.0     0.0     0.0     0.0     0.0     0.0     0.0
DL-Comp   : M       0.0     0.0     0.0     0.0     0.0     0.0     0.0
DW(Min)     V       0.0     0.0     0.0     0.0     0.0     0.0     0.0
LL + I    : M+      0.0     0.0     0.0     0.0     0.0     0.0     0.0
            V       0.0     0.0     0.0     0.0     0.0     0.0     0.0
LL + I    : M-      0.0     0.0     0.0     0.0     0.0     0.0     0.0
            V       0.0     0.0     0.0     0.0     0.0     0.0     0.0
LL + I    : Vmx     0.0     0.0     0.0     0.0     0.0     0.0     0.0
            M       0.0     0.0     0.0     0.0     0.0     0.0     0.0
Total     : M+    465.4   387.1   277.3   141.6    62.2    94.3     0.0
            V      12.8    22.3    28.2    34.2    37.2    36.0    39.4
Total     : M-      0.0     0.0     0.0     0.0     0.0     0.0     0.0
            V       0.0     0.0     0.0     0.0     0.0     0.0     0.0
Total     : Vmx    12.8    22.3    28.2    34.2    37.2    36.0    39.4
            M     336.5   278.4   199.3   101.7    44.7    67.7     0.0
 

 
REACTIONS (kips), STRENGTH I
---------
 
Load Type          Left Support     Right Support
---------          ------------     -------------
Self Wt.               10.6             10.6
Deck+Haunch             0.0              0.0
Diaphragm               0.1              0.1
DL-Prec.(DC)           19.8              9.1
DL-Prec.(DW)           12.8             19.6
DL-Comp.(DC)            0.0              0.0
DL-Comp.(DW)            0.0              0.0
Live                    0.0              0.0
        Truck           0.0              0.0
        Lane            0.0              0.0
Pedestrian              0.0              0.0
 
Upward reactions are positive.
Live Load reactions are per lane with no distribution factor and no impact.
Reactions are not multiplied by Load Modifiers (ductility, redundancy and operational importance).
Non-composite load types are per beam.
Composite and Pedestrian load types are per total bridge width.

 
Span : 1, Beam : 1, SERVICE I
 
RELEASE STRESSES, (ksi) (LOSS =  0.00 %)
 
               Trans   0.10L   0.20L   0.30L   0.40L Midspan Depress.
                      /0.90L  /0.80L  /0.70L  /0.60L
Location, ft    3.00    4.35    8.70   13.05   17.40   21.75   15.23
 
Beam-Self
Precast-top    0.103   0.144   0.256   0.336   0.384   0.400   0.364 
Bottom        -0.078  -0.109  -0.194  -0.255  -0.291  -0.304  -0.276 
 
Prestress
Precast-top    0.018   0.018   0.018   0.018   0.018   0.018   0.018 
Bottom         1.877   1.877   1.877   1.877   1.877   1.877   1.877 
 
Total
Precast-top    0.121   0.163   0.275   0.355   0.403   0.419   0.383 
Bottom         1.799   1.768   1.683   1.622   1.586   1.573   1.601 


 
 
SERVICE I
 
POSITIVE ENVELOPE STRESSES, (ksi) (LOSS = 11.95 %)
             Bearing   Trans     H/2   0.10L   0.20L   0.30L   0.40L Midspan
                                      /0.90L  /0.80L  /0.70L  /0.60L
 
Location, ft    0.00    2.50    1.63    3.85    8.20   12.55   16.90   21.25
 
Prestress
Precast-top    0.003   0.016   0.012   0.016   0.016   0.016   0.016   0.016
Bottom         0.286   1.653   1.186   1.653   1.653   1.653   1.653   1.653
 
Self wt.
Precast-top   -0.000   0.085   0.056   0.126   0.238   0.318   0.366   0.382
Bottom        -0.000  -0.064  -0.043  -0.095  -0.180  -0.241  -0.278  -0.290
 
DL-Prec (DC)
Precast-top   -0.000   0.156   0.104   0.229   0.416   0.528   0.563   0.522
Bottom        -0.000  -0.118  -0.079  -0.174  -0.316  -0.400  -0.427  -0.396
 
DL-Prec (DW)
Precast-top   -0.000   0.089   0.058   0.136   0.281   0.417   0.543   0.640
Bottom        -0.000  -0.068  -0.045  -0.103  -0.213  -0.316  -0.412  -0.486
 
Diaphragm
Precast-top   -0.000   0.001   0.000   0.001   0.002   0.004   0.005   0.006
Bottom        -0.000  -0.001  -0.000  -0.001  -0.002  -0.003  -0.004  -0.005
 
Deck + Haunch
Precast-top   -0.000  -0.000  -0.000  -0.000  -0.000  -0.000  -0.000  -0.000
Bottom        -0.000  -0.000  -0.000  -0.000  -0.000  -0.000  -0.000  -0.000
 
DL-Comp (DC)
Precast-top   -0.000  -0.000  -0.000  -0.000  -0.000  -0.000  -0.000  -0.000
Bottom        -0.000  -0.000  -0.000  -0.000  -0.000  -0.000  -0.000  -0.000
 
DL-Comp (DW)
Precast-top   -0.000  -0.000  -0.000  -0.000  -0.000  -0.000  -0.000  -0.000
Bottom        -0.000  -0.000  -0.000  -0.000  -0.000  -0.000  -0.000  -0.000
 
LL+I(+)
Precast-top   -0.000  -0.000  -0.000  -0.000  -0.000  -0.000  -0.000  -0.000
Bottom        -0.000  -0.000  -0.000  -0.000  -0.000  -0.000  -0.000  -0.000
 
Final 1 (P/S + DL + LL)
Precast-top    0.003   0.346   0.231   0.509   0.954   1.283   1.494   1.567 
Bottom         0.286   1.402   1.018   1.279   0.941   0.692   0.532   0.477 
 
Final 2 (P/S + DL)
Precast-top    0.003   0.346   0.231   0.509   0.954   1.283   1.494   1.567 
Bottom         0.286   1.402   1.018   1.279   0.941   0.692   0.532   0.477 
 

 
Span : 1, Beam : 1, SERVICE III
 
RELEASE STRESSES, (ksi) (LOSS =  0.00 %)
 
               Trans   0.10L   0.20L   0.30L   0.40L Midspan Depress.
                      /0.90L  /0.80L  /0.70L  /0.60L
Location, ft    3.00    4.35    8.70   13.05   17.40   21.75   15.23
 
Beam-Self
Precast-top    0.103   0.144   0.256   0.336   0.384   0.400   0.364 
Bottom        -0.078  -0.109  -0.194  -0.255  -0.291  -0.304  -0.276 
 
Prestress
Precast-top    0.018   0.018   0.018   0.018   0.018   0.018   0.018 
Bottom         1.877   1.877   1.877   1.877   1.877   1.877   1.877 
 
Total
Precast-top    0.121   0.163   0.275   0.355   0.403   0.419   0.383 
Bottom         1.799   1.768   1.683   1.622   1.586   1.573   1.601 
 
As_top  , in2  0.000   0.000   0.000   0.000   0.000   0.000   0.000 
Ast_prvd, in2  0.880   0.880   0.880   0.880   0.880   0.880   0.880 


 
 
SERVICE III
 
POSITIVE ENVELOPE STRESSES, (ksi) (LOSS = 11.95 %)
             Bearing   Trans     H/2   0.10L   0.20L   0.30L   0.40L Midspan
                                      /0.90L  /0.80L  /0.70L  /0.60L
 
Location, ft    0.00    2.50    1.63    3.85    8.20   12.55   16.90   21.25
 
Prestress
Precast-top    0.003   0.016   0.012   0.016   0.016   0.016   0.016   0.016
Bottom         0.286   1.653   1.186   1.653   1.653   1.653   1.653   1.653
 
Self wt.
Precast-top   -0.000   0.085   0.056   0.126   0.238   0.318   0.366   0.382
Bottom        -0.000  -0.064  -0.043  -0.095  -0.180  -0.241  -0.278  -0.290
 
DL-Prec (DC)
Precast-top   -0.000   0.156   0.104   0.229   0.416   0.528   0.563   0.522
Bottom        -0.000  -0.118  -0.079  -0.174  -0.316  -0.400  -0.427  -0.396
 
DL-Prec (DW)
Precast-top   -0.000   0.089   0.058   0.136   0.281   0.417   0.543   0.640
Bottom        -0.000  -0.068  -0.045  -0.103  -0.213  -0.316  -0.412  -0.486
 
Diaphragm
Precast-top   -0.000   0.001   0.000   0.001   0.002   0.004   0.005   0.006
Bottom        -0.000  -0.001  -0.000  -0.001  -0.002  -0.003  -0.004  -0.005
 
Deck + Haunch
Precast-top   -0.000  -0.000  -0.000  -0.000  -0.000  -0.000  -0.000  -0.000
Bottom        -0.000  -0.000  -0.000  -0.000  -0.000  -0.000  -0.000  -0.000
 
DL-Comp (DC)
Precast-top   -0.000  -0.000  -0.000  -0.000  -0.000  -0.000  -0.000  -0.000
Bottom        -0.000  -0.000  -0.000  -0.000  -0.000  -0.000  -0.000  -0.000
 
DL-Comp (DW)
Precast-top   -0.000  -0.000  -0.000  -0.000  -0.000  -0.000  -0.000  -0.000
Bottom        -0.000  -0.000  -0.000  -0.000  -0.000  -0.000  -0.000  -0.000
 
LL+I(+)
Precast-top   -0.000  -0.000  -0.000  -0.000  -0.000  -0.000  -0.000  -0.000
Bottom        -0.000  -0.000  -0.000  -0.000  -0.000  -0.000  -0.000  -0.000
 
Final 1 (P/S + DL + LL)
Precast-top    0.003   0.346   0.231   0.509   0.954   1.283   1.494   1.567 
Bottom         0.286   1.402   1.018   1.279   0.941   0.692   0.532   0.477 
 

 
VERTICAL SHEAR (Art. 5.8) - Span : 1, Beam : 1,  STRENGTH I
Using General Beta Theta Equation procedure - Art.5.7.3.4
Location (ft)
     Vu      bv    de     Aps      Vp    eps_x  Theta  Vs-reqd    Av/s    Av-prvd   Al_reqd
   (kips)   (in)  (in)   (in2)   (kips)                 (kips)  (in2/ft)  (in2/ft)   (in2)

    Mcor     a     dv      fpo   vu/fc   Vc-com  Beta  Max.spc.  min.Av/s  pVn/Vu       
    (kft)   (in)  (in)    (ksi)          (kips)          (in)    (in2/ft)             
*******************************************************************************************
Bearing :   0.50
     43.3    6.0   35.5    0.220   0.0   6.00e-3 50.0     35.2     0.241    3.013      0.00
      0.0    1.3   34.8     31.5 0.046      12.9 0.87    24.00     0.085    5.431 
Transfer:   3.00
     38.7    6.0   35.5    1.322   0.0  -0.20e-3 28.3      0.0     0.085    1.131      0.00
     84.6    9.6   31.9    189.0 0.045      76.6 5.65    24.00     0.085    5.578 
Critical:   3.16
     38.3    6.0   35.5    1.337   0.0  -0.21e-3 28.3      0.0     0.085    1.131      0.00
     90.4    9.8   31.9    189.0 0.044      76.9 5.67    24.00     0.085    5.638 
0.1L    :   4.35
     36.2    6.0   35.5    1.415   0.0  -0.21e-3 28.3      0.0     0.085    1.017      0.00
    125.7   10.5   31.9    189.0 0.042      77.5 5.72    24.00     0.085    5.965 
0.2L    :   8.70
     28.1    6.0   35.5    1.713   0.0  -0.24e-3 28.2      0.0     0.085    0.816      0.00
    236.4   13.3   31.9    189.0 0.033      79.2 5.84    24.00     0.085    7.679 
0.3L    :  13.05
     20.0    6.0   35.5    1.736   0.0  -0.22e-3 28.2      0.0     0.085    0.282      0.00
    313.8   13.5   31.9    189.0 0.023      77.8 5.74    24.00     0.085    7.277 
0.4L    :  17.40
     12.3    6.0   35.5    1.736   0.0  -0.21e-3 28.3      0.0     0.085    0.282      0.00
    358.1   13.5   31.9    189.0 0.014      77.1 5.69    24.00     0.085   11.762 
0.5L    :  21.75
     11.0    6.0   35.5    1.736   0.0  -0.21e-3 28.3      0.0     0.085    0.563      0.00
    366.0   13.5   31.9    189.0 0.013      77.0 5.68    24.00     0.085   19.590 
0.6L    :  26.10
     12.8    6.0   35.5    1.736   0.0  -0.22e-3 28.2      0.0     0.085    0.282      0.00
    336.5   13.5   31.9    189.0 0.015      77.7 5.73    24.00     0.085   11.349 
0.7L    :  30.45
     22.3    6.0   35.5    1.736   0.0  -0.23e-3 28.2      0.0     0.085    0.282      0.00
    278.4   13.5   31.9    189.0 0.026      78.7 5.81    24.00     0.085    6.578 
0.8L    :  34.80
     28.2    6.0   35.5    1.713   0.0  -0.25e-3 28.1      0.0     0.085    0.816      0.00
    199.3   13.3   31.9    189.0 0.033      80.3 5.93    24.00     0.085    7.642 
0.9L    :  39.15
     34.2    6.0   35.5    1.415   0.0  -0.23e-3 28.2      0.0     0.085    1.017      0.00
    101.7   10.5   31.9    189.0 0.040      78.4 5.78    24.00     0.085    6.314 
Critical:  40.34
     35.7    6.0   35.5    1.337   0.0  -0.21e-3 28.3      0.0     0.085    1.131      0.00
     72.8    9.8   31.9    189.0 0.041      77.3 5.70    24.00     0.085    6.041 
Transfer:  40.50
     36.0    6.0   35.5    1.322   0.0  -0.21e-3 28.3      0.0     0.085    1.131      0.00
     67.7    9.6   31.9    189.0 0.042      77.0 5.68    24.00     0.085    5.990 
Bearing :  43.00
     39.4    6.0   35.5    0.220   0.0   6.00e-3 50.0     30.9     0.211    3.013      0.00
      0.0    1.3   34.8     31.5 0.042      12.9 0.87    24.00     0.085    5.966 
 

ANCHORAGE ZONE REINFORCEMENT (Art. 5.9.4.4)
Span : 1, Beam : 1
Fpi,       kips =  425.36
fs,         ksi =   20.00
h/4,         in =    9.75
Abrst_rqrd, in2 =    0.85

CAMBER AND DEFLECTIONS: SERVICE I ( Span : 1, Beam : 1; Units: in )
 
               :     Release  Mult   Erection  Mult      Final
At 0.1 x L = 3.85 ft
Prestress      :       0.141  1.80      0.254  2.45      0.346
Self Wt.       :      -0.040  1.85     -0.073  2.70     -0.107
Deck + Haunch  :                        0.000  2.30      0.000
DL-Prec. (DC)  :                       -0.046  3.00     -0.139
Diaphragm      :                       -0.000  3.00     -0.001
DL-Prec. (DW)  :                       -0.045  3.00     -0.136
DL-Comp. (DC)  :                        0.000  3.00      0.000
DL-Comp. (DW)  :                        0.000  3.00      0.000
Live Load      : Not Included
Total          :       0.102            0.089           -0.037
 
At 0.2 x L = 8.20 ft
Prestress      :       0.253  1.80      0.455  2.45      0.620
Self Wt.       :      -0.075  1.85     -0.138  2.70     -0.202
Deck + Haunch  :                        0.000  2.30      0.000
DL-Prec. (DC)  :                       -0.092  3.00     -0.276
Diaphragm      :                       -0.001  3.00     -0.002
DL-Prec. (DW)  :                       -0.093  3.00     -0.278
DL-Comp. (DC)  :                        0.000  3.00      0.000
DL-Comp. (DW)  :                        0.000  3.00      0.000
Live Load      : Not Included
Total          :       0.178            0.131           -0.139
 
At 0.3 x L = 12.55 ft
Prestress      :       0.333  1.80      0.599  2.45      0.815
Self Wt.       :      -0.102  1.85     -0.189  2.70     -0.277
Deck + Haunch  :                        0.000  2.30      0.000
DL-Prec. (DC)  :                       -0.126  3.00     -0.379
Diaphragm      :                       -0.001  3.00     -0.003
DL-Prec. (DW)  :                       -0.132  3.00     -0.396
DL-Comp. (DC)  :                        0.000  3.00      0.000
DL-Comp. (DW)  :                        0.000  3.00      0.000
Live Load      : Not Included
Total          :       0.230            0.150           -0.239
 
At 0.4 x L = 16.90 ft
Prestress      :       0.381  1.80      0.685  2.45      0.933
Self Wt.       :      -0.120  1.85     -0.222  2.70     -0.324
Deck + Haunch  :                        0.000  2.30      0.000
DL-Prec. (DC)  :                       -0.146  3.00     -0.437
Diaphragm      :                       -0.001  3.00     -0.004
DL-Prec. (DW)  :                       -0.159  3.00     -0.478
DL-Comp. (DC)  :                        0.000  3.00      0.000
DL-Comp. (DW)  :                        0.000  3.00      0.000
Live Load      : Not Included
Total          :       0.261            0.157           -0.310
 
At 0.5 x L = 21.25 ft
Prestress      :       0.397  1.80      0.714  2.45      0.972
Self Wt.       :      -0.126  1.85     -0.233  2.70     -0.340
Deck + Haunch  :                        0.000  2.30      0.000
DL-Prec. (DC)  :                       -0.149  3.00     -0.446
Diaphragm      :                       -0.001  3.00     -0.004
DL-Prec. (DW)  :                       -0.171  3.00     -0.514
DL-Comp. (DC)  :                        0.000  3.00      0.000
DL-Comp. (DW)  :                        0.000  3.00      0.000
Live Load      : Not Included
Total          :       0.271            0.159           -0.333
 
At 0.6 x L = 25.60 ft
Prestress      :       0.381  1.80      0.685  2.45      0.933
Self Wt.       :      -0.120  1.85     -0.222  2.70     -0.324
Deck + Haunch  :                        0.000  2.30      0.000
DL-Prec. (DC)  :                       -0.137  3.00     -0.412
Diaphragm      :                       -0.001  3.00     -0.004
DL-Prec. (DW)  :                       -0.165  3.00     -0.495
DL-Comp. (DC)  :                        0.000  3.00      0.000
DL-Comp. (DW)  :                        0.000  3.00      0.000
Live Load      : Not Included
Total          :       0.261            0.160           -0.302
 
At 0.7 x L = 29.95 ft
Prestress      :       0.333  1.80      0.599  2.45      0.815
Self Wt.       :      -0.102  1.85     -0.189  2.70     -0.277
Deck + Haunch  :                        0.000  2.30      0.000
DL-Prec. (DC)  :                       -0.113  3.00     -0.339
Diaphragm      :                       -0.001  3.00     -0.003
DL-Prec. (DW)  :                       -0.141  3.00     -0.422
DL-Comp. (DC)  :                        0.000  3.00      0.000
DL-Comp. (DW)  :                        0.000  3.00      0.000
Live Load      : Not Included
Total          :       0.230            0.155           -0.226
 
At 0.8 x L = 34.30 ft
Prestress      :       0.253  1.80      0.455  2.45      0.620
Self Wt.       :      -0.075  1.85     -0.138  2.70     -0.202
Deck + Haunch  :                        0.000  2.30      0.000
DL-Prec. (DC)  :                       -0.079  3.00     -0.238
Diaphragm      :                       -0.001  3.00     -0.002
DL-Prec. (DW)  :                       -0.101  3.00     -0.303
DL-Comp. (DC)  :                        0.000  3.00      0.000
DL-Comp. (DW)  :                        0.000  3.00      0.000
Live Load      : Not Included
Total          :       0.178            0.136           -0.125
 
At 0.9 x L = 38.65 ft
Prestress      :       0.141  1.80      0.254  2.45      0.346
Self Wt.       :      -0.040  1.85     -0.073  2.70     -0.107
Deck + Haunch  :                        0.000  2.30      0.000
DL-Prec. (DC)  :                       -0.039  3.00     -0.116
Diaphragm      :                       -0.000  3.00     -0.001
DL-Prec. (DW)  :                       -0.050  3.00     -0.150
DL-Comp. (DC)  :                        0.000  3.00      0.000
DL-Comp. (DW)  :                        0.000  3.00      0.000
Live Load      : Not Included
Total          :       0.102            0.092           -0.028
 

ULTIMATE - Span : 1, Beam : 1,  STRENGTH I
(Mr-prvd computed by AASHTO equations, Art. 5.7.3.2/5.7.3.3)
 

Location (ft)
    Mu       dp    Aps    fps     c      a    Mr-prvd eps_t   Phi   Mcr    min Mr  Crkg  Mu-p/r
   k.ft      in    in2    ksi     in     in    k.ft                 k.ft    k.ft   Ratio Ratio
**********************************************************************************************
Transfer:   2.50
   102.5    29.2  1.652  238.9   12.0   9.65    830.8  0.006T 1.00       -       -     -     -  
H/2     :   1.63
    67.9    29.2  1.170  251.6    7.1   5.72    650.9  0.013T 1.00       -       -     -     -  
0.1L    :   3.85
   153.0    29.2  1.768  236.1   13.1  10.54    866.8  0.005T 1.00       -       -     -     -  
0.2L    :   8.20
   292.7    29.2  2.141  227.3   16.5  13.26    864.5  0.004I 0.89       -       -     -     -  
0.3L    :  12.55
   397.3    29.2  2.170  226.7   16.7  13.45    862.4  0.004I 0.89    830.1   528.4    1.04    -  
0.4L    :  16.90
   466.8    29.2  2.170  226.7   16.7  13.45    862.4  0.004I 0.89    830.1   620.8    1.04    -  
0.5L    :  21.25
   494.1    29.2  2.170  226.7   16.7  13.45    862.4  0.004I 0.89    830.1   657.2    1.04    -  
0.6L    :  25.60
   465.4    29.2  2.170  226.7   16.7  13.45    862.4  0.004I 0.89    830.1   618.9    1.04    -  
0.7L    :  29.95
   387.1    29.2  2.170  226.7   16.7  13.45    862.4  0.004I 0.89    830.0   514.9    1.04    -  
0.8L    :  34.30
   277.3    29.2  2.141  227.3   16.5  13.26    864.5  0.004I 0.89    830.0   368.8    1.04    -  
0.9L    :  38.65
   141.6    29.2  1.768  236.1   13.1  10.54    866.8  0.005T 1.00       -       -     -     -  
H/2     :  40.88
    62.2    29.2  1.170  251.6    7.1   5.72    650.9  0.013T 1.00       -       -     -     -  
Transfer:  40.00
    94.3    29.2  1.652  238.9   12.0   9.65    830.8  0.006T 1.00       -       -     -     -  

Legend: C = Compression-Controlled (0 < eps_t < 0.0020)
        I = In-Transition (0.0020 <= eps_t < 0.0050)
        T = Tension-Controlled (eps_t <= 0 or eps_t >= 0.0050)

Note  : fr used for calculating Mcr is computed using AASHTO method (Art.5.4.2.6.)

Consider Bottom Tension Steel Contribution : NO

 
 
DETENSIONING ( Span : 1, Beam : 1; Groups 1-7; Units: ksi )
 
Grp Str    Ys,in       3.00ft

  1   2 E   2.00 Ft    -0.128
        M   2.00 Fb     0.475
 
  2   1 E  36.00 Ft     0.268
        M  36.00 Fb     0.364
 
  3   1 E  34.00 Ft     0.634
        M  34.00 Fb     0.275
 
  4   2 E   6.00 Ft     0.523
        M   6.00 Fb     0.738
 
  5   1 E   6.00 Ft     0.468
        M   6.00 Fb     0.969
 
  6   2 E   2.00 Ft     0.237
        M   2.00 Fb     1.522
 
  7   1 E   2.00 Ft     0.121
        M   2.00 Fb     1.799
 
 

DESIGN SUMMARY
--------------
Span:  1,   Beam:  1,   Exterior beam
Beam type: I-Girder       , IA-Std-B       
Precast Length, ft: 43.50            Release Length, ft: 43.50
Strand Pattern: Straight              
Strand: 0.6''-LL-270-72.6       
Strand Es, ksi:    28500.0            No. of strands:  10
No. of strands, Draped:   0           No. of strands, Straight:  10
Concrete Strength, f'ci:   4.5  ksi        f'c:   5.0 ksi  f'ct   4.0 ksi
Initial losses:  4.39 %               Final losses: 15.08 %
 
Specification
-------------                            Allowable   Computed   Location    Status
Release Stresses (ksi) (Art. 5.9.2.3)
      Precast Bot (compression)             2.930       1.799     Trans       OK
      Precast Top w/ no reinf. (tension)   -0.190       0.121       Trans
      Precast Top w/ reinf. (tension)      -0.510           
Strength I (Art. 3.4.1, 5.6.3.1)       Provided     Required   Location   Status
      Ult. Moment (k.ft)                   866.78      494.12     Midspan     OK
Debonding Limits (Art. 5.9.4.3.3)         Allowable    Computed              Status
      Max. Debond per Row                  40.00 %       0.00 %               OK
      Max. Debond Total                    25.00 %       0.00 %               OK
 
                       Final 1                     Final 2                     Final 3
Specification  Allow.  Comp.      Loc.     Allow.   Comp.      Loc.     Allow.   Comp.      Loc.
-------------  -----------------------     -------------------------     ------------------------
Positive Moment Envelope Stresses (ksi) (Art. 3.4.1 and 5.9.2.3.2)
  Service I Limit State - Compressive Stresses Only
    Pre.Top:   3.000   1.567     Midspan    2.250   1.567     Midspan
    Pre.Bot:   3.000   1.402    Transfer    2.250   1.402    Transfer
  Service III Limit State - Tensile Stresses Only
    Pre.Top:  -0.000   0.003     Bearing
    Pre.Bot:  -0.000   0.286     Bearing
 
CAMBER / DEFLECTION: (PCI Design Handbook - 7th Ed.- Table 5.8.2)
0.5 x L =  21.25 ft
               :     Release  Mult   Erection  Mult      Final
Prestress      :       0.397  1.80      0.714  2.45      0.972
Self Wt.       :      -0.126  1.85     -0.233  2.70     -0.340
Deck + Haunch  :                        0.000  2.30      0.000
DL-Prec. (DC)  :                       -0.149  3.00     -0.446
Diaphragm      :                       -0.001  3.00     -0.004
DL-Prec. (DW)  :                       -0.171  3.00     -0.514
DL-Comp. (DC)  :                        0.000  3.00      0.000
DL-Comp. (DW)  :                        0.000  3.00      0.000
Live Load      : Not Included
 
Total          :       0.271            0.159           -0.333
 
Positive values indicate upward deflection.

LIVE LOADS - NONE
 
RATING LOADS - NONE

